Solved: Honeywell Thermostat Error Codes

|

A Honeywell smart thermostat is a great way to better manage how you use your heating and cooling. But like any technology, you may sometimes run across a problem. With its digital display, Honeywell smart thermostats can display an error code that certified technicians can use to get a better sense of what’s happening. Here are several of the most likely error codes you might see on your Honeywell smart thermostat.

Honeywell Thermostat Error e42

You may receive this error code if your home’s Wi-Fi internet did not provide an IP address for the thermostat to connect to. This can take place if your router fails to perform the Dynamic Host Configuration Protocol or DHCP. This function automatically transmits the required IP address for your thermostat to link up.

How to Fix Honeywell Thermostat Error e42

You can clear error code e42 by making sure that your router has enabled DHCP. Assuming it does, you may also have to power cycle the router and repeat the initial setup process with your thermostat. Completing this task should see to it that the DHCP is sent and connects to the smart thermostat.

Honeywell Thermostat Error e02

Error code e02 is displayed when the password for accessing your home’s Wi-Fi router is not correct. When this error code appears for 30 seconds, the thermostat’s digital display automatically transitions to the Wi-Fi setup screen so you can attempt to enter the password again.

How to Fix Honeywell Thermostat Error e02

All you have to do to clear error e02 is make sure you’re entering the correct Wi-Fi password when configuring the thermostat.

Honeywell Thermostat Error 40

Error code 40 can pop up when the thermostat is notified that a heat pump or air conditioner’s monitoring system has detected a malfunction. For the most part, this happens once the compressor isn’t turning on despite being instructed to. But this error code could also appear if power is disconnected from the outdoor unit for an extended period. A “High-Pressure Fault” error, triggered by obstructed airflow, can render this error code. Lastly, you may encounter error code 40 if there’s something wrong with the coolant, the outdoor unit’s fan motor, or the motor’s starting capacitor.

How to Fix Honeywell Thermostat Error 40

You can check the air filter for signs of a clog, as well as the breakers and indoor unit’s blower for ordinary operation. If you reset the thermostat and error code 40 reappears, it’s best to contact an experienced technician.

Honeywell Thermostat Error e43

If a Honeywell thermostat displays error code e43, it is failing to communicate with the router, and by extension your Wi-Fi. This may happen if the router’s ethernet cable isn’t plugged in or it isn’t communicating with your wide area network (WAN).

How to Fix Honeywell Thermostat Error e43

Reset the router by unplugging it and leaving it that way for around 30 seconds. The thermostat might also be disconnected if you recently updated the password or the Wi-Fi’s SSID, which is the name you give it.

Honeywell Thermostat Error e1

Thermostats utilize sensors to identify the temperature outdoors and indoors. If a sensor fails, you may see error code e1 show up on your Honeywell smart thermostat.

How to Fix Honeywell Thermostat Error e1

A trained technician can change out the sensor and reboot the thermostat, which should resolve error code e1.

Honeywell Thermostat Error 11n

Error code 11n could appear in situations where the thermostat can’t recognize a heating or cooling unit. This might mean that the equipment itself is malfunctioning and unable to connect to the thermostat. This sometimes happens when the wiring is damaged or even if the thermostat is faulty.

How to Fix Honeywell Thermostat Error 11n

A professional technician can employ a voltmeter to find out if there’s a poor electrical connection. When the wiring on your specific HVAC system is bad, the technician can replace it. In situations where the thermostat itself is the issue, it will likely have to be replaced.

Honeywell Thermostat Error e2

If you see error code e2 pop up on your Honeywell smart thermostat, it could mean a couple of different things. For example, one of the sensors used to detect the temperature isn’t functioning correctly. In other instances, it means the router was disconnected from power before the thermostat could complete the setup process.

How to Fix Honeywell Thermostat Error e2

In situations where the error code stems from sensor failure, a technician can troubleshoot and switch out the impacted sensor. When the problem stems from disconnected power, all you’ll need to do is see to it that the router remains on throughout the setup process.

The post Solved: Honeywell Thermostat Error Codes appeared first on Air Houston Mechanical LLC.

Categories: